The purpose of PMI is to ensure that materials are correctly supplied and/or installed, as specified. This guideline is applicable to pressure-retaining equipment and piping fabricated from Cr-Mo, owCr-Ni-Mo, Ni alloy steel, Ni based alloys, and other alloys as specified in the Purchase Order and/or related documents.
Materials requiring PMI per this guideline are identified in Table 1. Components exempt from PMI are listed folling Table 2. When required by the Purchase Order, PMI testing shall be performed on each alloy component of a pressure-retaining assembly. This shall include each individual segment of pipe, welds, each plate, and other base materials (i.e., forgings, fittings,
furnace tubing, tube sheets, etc.) provided by the Seller. Alloy portion of clad and/or weld overlay components shall receive PMI testing, regardless of whether the cladding or overlay has been considered in the pressure calculations. Carbon steel components are exempt from PMI unless alloying elements are critical to corrosion resistance, therefore a requirement for PMI of CS will be noted in the Purchase Order. As an example, a minimum of 0.10% silicon content is critical to the corrosion resistance of carbon steels in sulfidizing environments.
Table 1: Materials and Components Requiring PMI
| ITEM | VERIFICATION REQUIRED |
| Carbon Steels1 or Cast Irons | No – Unless noted in P.O. |
| Alloy Pressure Piping (Spools, Fittings, Straight-Run Pipe) | Yes – 100% |
| Alloy Pressure Vessels Components (Pressure retaining) | Yes – 100% |
| Alloy Valves | Yes – 100% Body, Bonnet, stem only, as designated by P.O. |
| Alloy Pumps | Yes – 100% Casing/Impeller only |
| Alloy Tubing (1/2” diameter and smaller) | No |
| Alloy Instrumentation, Pressure Chambers | Yes – 100% |
| Alloy Bolting – A193 B7/ B16, A320 L7 | Yes – 1% of total studs/bolts, 1 check per heat (min.) |
| SS Bolting – A193/A320 B8/B8M | Yes – 1% of total studs/bolts, 1 check per heat (min.) |
| Alloy Heat Exchanger Tubing | Yes – 2.5% of total tubes, minimum one check per heat |
| Carbon steel welds (pressure retaining) | No – Unless noted in P.O. |
| Alloy Pressure Retaining Welds in Contact with Process Fluids | Yes – 100% of completed welds (cap or root) |
| 304/304L Stainless steel welds | No – Unless noted in P.O. |
| Other SS pressure retaining welds | Yes – 100% in accordance with this specification |
| Alloy Weld Overlay | Yes – 100% in accordance with this specification & component specific fabrication specification. |
| Alloy RTJ (Ring) Gaskets | Yes – 100% (1 test per each heat) |
| Alloy Cladding | Yes – Once per piping component or fitting, and each shell course component (e.g., HEX channel) for equipment. |
The following items are exempt from PMI, unless specifically designated for PMI by the Purchase Order:
a) Alloy components where the alloy is installed for product purity considerations, including lube oil, and seal oil piping and tubing.
b) 300 series stainless steel selected for Cryogenic application or specifically for resistance to Wet CO2.
c) Internal machinery parts.
d) Internal instruments parts (including pressure parts of gages)
e) Internal non-pressure retaining baffles, trays, tray clips, supports, pall-rings, support rings, etc.
f) Electrical components.
g) Non-pressure containing welds.
h) Internal valve components.
i) Alloy components that have been substituted as a “higher” alloy for Carbon Steel or substitutions such as 316 for 304 or B8M for B8.
j) Gaskets (except RTJ gaskets).
k) Copper alloys; Titanium and it’s alloys; Brass and Bronze alloys.
l) Off-the-shelf (e.g., “buy what they make” components)
Table 2: Critical Elements Required for PMI
| Alloy Categories & Specific Alloys | Elements to be Verified |
| 300 Series Stainless (304, 316L, 310, 321, 347, etc.) | Cr, Ni, Mo (plus: Cb or Ti for “stabilized” grades (321 & 347); Carbon may also be required if specifically noted in the P.O.; For 304 Cr, Ni shall be verified) |
| 6-Mo (AL6XN, 254SMo, 904L, etc.) | Cr, Ni, Mo, Cu |
| Ni-Based (Alloy C-22, Alloy 625, Monel, etc.) | Ni, Cr, Mo, W, Cu |
| Low-Alloy, General (1¼ Cr-½ Mo, 2¼ Cr-1Mo, 5 Cr-1½ Mo, etc.) | Cr, Mo |
| Low-Alloy, 9 Chrome and Grade 91 (9 Cr-1 Mo and 9 Cr-1 Mo-V Modified) | Cr, Mo, V |
| 400 Series Stainless (405, 410, 410S, etc.) | Cr (plus: C & Ni, for “S” grades, if specifically noted in the P.O.) |
| CA6NM | Cr, Ni, Mo |
| Duplex Stainless (2205, 3RE60, CD-4MCu, Uranus 50, etc.) | Cr, Ni, Mo, Cu |
| Low-Ni Steel (3½ Ni, 9 Ni, etc.) | Ni |
